OBD-II adapters#
OpenCarMind talks to the car through a Bluetooth LE adapter that speaks the ELM327 command set. This page lists the adapters the firmware was written to support, what each one uses on the radio, and where to buy it.
Only the LELink has been driven with this board. Every other row is based on the adapter’s published Bluetooth layout or on what other open-source OBD projects use for it. If you try one, please report the result with the Field check issue template so the table can move from “expected” to “tested”.
What the board needs from an adapter#
Bluetooth LE. The ESP32-S3 has no Classic Bluetooth radio, so adapters that only offer Bluetooth 3.0 (SPP) cannot connect. Many cheap adapters sold as “Android only” are Classic.
ELM327 or STN commands. Adapters that only work with their own app and speak a private protocol will connect, fail the ELM327 reset, and be skipped.
How the board finds and talks to an adapter#
It scans and collects candidates for 1.5 s, then connects to the one with the strongest signal. A device counts as a candidate when its name contains a word adapters use (OBD, ELM327, Vgate, vLink, Veepeak, Carista, Kiwi, LELink, Konnwei, Viecar and others), when its name starts with an entry of
OBD_BLE_NAME_PREFIXES, or when it advertises a service that OBD adapters use (FFF0, 18F0, BEEF, or the Vgate E7810A71 service).It reads the GATT table and picks the serial line. Known layouts are tried first, then the first non-standard service with a characteristic it can subscribe to (notify or indicate) and one it can write to.
It subscribes. If the adapter refuses because the link is not encrypted, the board pairs with Just Works and bonds. If Just Works is refused, it tries once more with the fixed PIN 123456, which OBDLink documents for its CX.
It sends
ATZ. The address is stored only after the device answers like an ELM327. A device that has no serial line, cannot be subscribed to, or never answers is skipped for 10 minutes and the scan moves on.Writes are cut to the negotiated MTU, and each piece waits for its acknowledgement.
If the ECU does not answer under automatic protocol search, the board tries each protocol in turn (CAN 11-bit 500k, CAN 11-bit 250k, J1850 PWM, CAN 29-bit 500k, CAN 29-bit 250k, J1850 VPW, ISO 9141-2, ISO 14230 slow and fast init).
Known serial layouts#
Layout |
Service |
Receive |
Send |
Seen on |
Source |
|---|---|---|---|---|---|
FFF0 |
FFF0 |
FFF1 (notify) |
FFF2 (write) |
OBDLink CX, Veepeak, Carista, most clones |
|
FFE0 |
FFE0 |
FFE1 |
FFE1 (same characteristic) |
LELink, HM-10 style clones |
tested on this board |
FFE0 split |
FFE0 |
FFE1 |
FFE2 |
adapters with the Deep OBD firmware |
|
Vgate E7810A71 |
E7810A71-73AE-499D-8C15-FAA9AEF0C3F2 |
BEF8D6C9-9C21-4C9E-B632-BD58C1009F9F |
same characteristic |
Vgate vLinker |
|
Vgate 18F0 |
18F0 |
2AF0 |
2AF1 |
Vgate iCar Pro BLE |
|
BEEF |
BEEF |
picked by property |
picked by property |
listed by LTSupportAutomotive |
|
Nordic UART |
6E400001-B5A3-F393-E0A9-E50E24DCCA9E |
6E400003 |
6E400002 |
some DIY and clone adapters |
Adapters#
Prices are in US dollars, taken from US listings seen on 3 November 2026 and change often. “Not found” means no current price showed up. Amazon links are plain product pages with no affiliate tag. Each one was opened on 3 November 2026 and showed the named product. Where the title does not name the model or the page showed the item unavailable, the Status column says so.
Adapter |
Radio |
Layout |
Status |
Price seen |
Buy |
|---|---|---|---|---|---|
LELink² |
BLE |
FFE0 |
Tested on this board |
not found |
Amazon B0755N61PW, original LELink B00QJRYMFC |
Veepeak OBDCheck BLE+ |
BLE (Classic too, for Android) |
FFF0 |
Expected |
about 38 to 42 USD at US retailers |
|
Veepeak OBDCheck BLE |
BLE 4.0 |
FFF0 |
Expected |
about 32 USD at a US retailer |
|
OBDLink CX (Amazon lists it as the Bimmercode edition, the only CX model) |
BLE 5.1 |
FFF0, always encrypted |
Expected, pairs on demand. Bonding is open for the first 5 minutes after the adapter powers up |
79.95 USD |
|
Vgate iCar Pro BLE 4.0 |
BLE, shows up as IOS-Vlink |
18F0 |
Expected |
31.49 USD |
|
Vgate vLinker MC+ |
BLE and Classic, BLE side named vLinker MC-IOS |
Vgate E7810A71 or generic |
Expected |
about 55 USD |
|
Vgate vLinker FS |
Classic and BLE, ships in MFi mode |
Vgate E7810A71 or generic |
Needs a setting: switch it to “BLE+BT” with the VgateFwUpdater app first |
not found |
|
Vgate vLinker MS |
Classic and BLE, ships in MFi mode |
Vgate E7810A71 or generic |
Needs a setting: switch it to “BLE+BT” with the VgateFwUpdater app first |
not found |
|
Carista OBD2 / Carista EVO |
BLE |
FFF0 |
Expected |
not found |
|
FIXD |
Bluetooth |
unknown |
Unverified. One owner reports it works with other ELM327 apps |
not found, first generation discontinued |
|
Generic “ELM327 BLE 4.0” clones |
BLE |
usually FFF0 or FFE0 |
Expected for most. Some fake v2.1 clones skip commands |
varies |
example: RODEDIO B0GWQKLTMR, whose listing says Bluetooth LE on iOS |
Panlong PL-B04 |
Bluetooth, iOS and Android |
generic |
Expected for the “For iOS Android” option: that listing says it works with Car Scanner on iOS, which needs BLE and ELM327. The “For Android Only” option is likely Classic. The page title does not name the model |
not found |
|
DA200 (sold as “OBD2 Scanner Bluetooth 5.4 with AI Repair Tips”) |
BLE 4.0 / 5.4 |
generic |
Expected: the maker’s spec sheet lists BLE, a PIC18F25K80 main chip (the chip most ELM327 v1.5 clones use) and all 9 OBD-II protocols. The Amazon title does not name the model, so check for DA200 on the box |
not found |
|
V800 full-system scanners (Panlong PL-V800, white-label copies such as VQQEFF) |
Bluetooth |
private app |
Not expected: the Panlong listing says it uses the INNOOBD+ app and does not support third-party apps. Its title says “Engine Transmission ABS SRS” and does not say V800 |
not found |
|
“OBD2 Scanner AI Diagnostic Tool” with an exclusive app |
Bluetooth |
unknown |
Unverified: the listing names no chip, no Bluetooth type and no third-party apps |
not found |
|
BlueDriver Bluetooth Pro |
Bluetooth |
private protocol |
Not expected: reported to work only with its own app |
79.95 USD |
|
OBDLink MX+ |
Classic Bluetooth 3.0 |
SPP |
Will not work, no Classic radio on the S3 |
139.95 USD |
|
OBDLink LX |
Classic Bluetooth 3.0 |
SPP |
Will not work, no Classic radio on the S3 |
not found |
|
KONNWEI KW902 |
Classic, listed for Android and Windows only |
SPP |
Will not work, no Classic radio on the S3. Listing showed “currently unavailable” on 3 Nov 2026 |
not found |
Not listed? Check your adapter with a BLE scanner app such as nRF Connect. A service with one characteristic that notifies or indicates and one you can write is enough for the generic fallback. When the name has none of the words above and the adapter advertises no known service, add its name to OBD_BLE_NAME_PREFIXES in idf.py menuconfig.
Sources for the adapter facts#
OBDLink CX layout, encryption, PIN, MTU and write rules: OBDLink CX adapter notes
OBDLink radios (CX is BLE 5.1, MX+ and LX are Bluetooth 3.0): Which OBDLink adapter is right for me?
Veepeak and Carista on FFF0: Stack Overflow 61090365
Vgate iCar Pro BLE on 18F0/2AF0/2AF1: ABRP request, SwiftOBD2 source
vLinker FS and MS MFi mode and the VgateFwUpdater switch: the Amazon listings linked above
BlueDriver app lock (secondary source): OBDplanet
DA200 spec sheet (V1.1, 15 April 2025): Global Sources PDF
Panlong PL-B04 and PL-V800 app support: the Amazon listings linked above
FIXD with other apps (one owner): iamcarhacker
Name words and fallback rules: BetterDriver, ha-obd-ble, SwiftOBD2
Protocol order after a failed auto search: python-OBD