Boards#
ESP32-S3 and the parts list#
Board: Waveshare ESP32-S3-LCD-1.47B (the pin map in
main/board.hmatches it).Or the Espressif ESP-Mosaico V1.2 (ESP32-S31) with the OpenCarMind EdgeOS 2.0.0 build (called mossREV up to 1.2.0). It needs no SD card: see docs/MOSAICO.md.
Adapter: a Bluetooth LE adapter that speaks ELM327 commands (see below). Classic Bluetooth adapters will not work, because the S3 has no classic radio.
A FAT-formatted SD card.
Adapter compatibility#
Only the LELink has been driven with this board. The other rows come from vendor documents and other open-source OBD projects. docs/ADAPTERS.md has prices and sources. The Amazon links are plain product pages with no affiliate tag, all opened on 3 November 2026.
Adapter |
Bluetooth |
Built-in profile |
Status |
Amazon |
|---|---|---|---|---|
LELink², LELink |
LE |
FFE0 / FFE1 |
tested |
|
Veepeak OBDCheck BLE+, BLE |
LE |
FFF0 / FFF1 / FFF2 |
expected |
|
OBDLink CX (sold as the Bimmercode edition, which is the only CX model) |
LE 5.1, encrypted |
FFF0 / FFF1 / FFF2, pairs on demand |
expected |
|
Carista OBD2, Carista EVO |
LE |
FFF0 / FFF1 / FFF2 |
expected |
|
Vgate iCar Pro BLE 4.0 |
LE |
18F0 / 2AF0 / 2AF1 |
expected |
|
Vgate vLinker MC+ |
LE and Classic |
E7810A71 / BEF8D6C9 |
expected |
|
Vgate vLinker FS, MS |
LE and Classic |
E7810A71 / BEF8D6C9 |
switch to “BLE+BT” in the VgateFwUpdater app first |
|
Panlong OBD2 Scanner (PL-B04) |
LE, works with Car Scanner on iOS |
generic fallback |
expected for the “For iOS Android” option only. The “For Android Only” option is likely Classic. The page title does not name the model |
|
DA200 (Bluetooth 5.4, “AI Repair Tips”) |
LE, PIC18F25K80 ELM327-type chip (maker’s spec sheet) |
generic fallback |
expected. The page title does not name the model, check for DA200 on the box |
|
ELM327 BLE clones (for example RODEDIO) |
LE on iOS |
FFF0 or FFE0 |
expected for most. Buy one whose listing says Bluetooth LE for iOS |
|
Adapters running the Deep OBD firmware |
LE |
FFE0 / FFE1 / FFE2 |
expected |
not sold on Amazon. Layout from the Deep OBD source, BtLeGattSppAndroid.cs |
FIXD |
Bluetooth |
unknown |
unverified |
|
BlueDriver |
Bluetooth |
private protocol |
not expected |
|
V800 full-system scanners (Panlong PL-V800 and white-label copies) |
Bluetooth |
private app (INNOOBD+) |
not expected. The title says “Engine Transmission ABS SRS”, not V800 |
|
OBDLink MX+, OBDLink LX, KONNWEI KW902 |
Classic only (LX: Bluetooth 3.0, KW902: Android and Windows only) |
none |
will not work. The KW902 listing showed “currently unavailable” on 3 Nov 2026 |
The ESP-Mosaico#
Part |
On the ESP-Mosaico V1.2 |
|---|---|
Chip |
ESP32-S31 (ESP32-S31NRV16), dual core, run at 320 MHz |
PSRAM |
32 MB in the package. The board’s user guide says 16 MB. The chip reports 33,554,432 bytes ( |
Flash |
16 MB NOR (GD25Q128): two 6 MB app slots, and 3.75 MB of FAT for the state files |
Drive-log store |
128 MB SPI NAND (GD5F1GM7UEYIGR) on its own SPI bus, see The 128 MB NAND |
Screen |
2.16 inch CO5300 AMOLED, 480 x 480, over QSPI |
Touch |
CST9220 on I2C |
Battery |
a small cell with a BQ27220 fuel gauge |
Radio |
Wi-Fi and Bluetooth. OpenCarMind uses Bluetooth LE for the OBD adapter, as on the S3 |
USB |
one Type-C port, the S31’s USB OTG port: console, the desktop app’s USB door, and flashing |
There is no SD card slot. The drive logs live on the NAND, and the learned model state, the clock, the settings files and the Wi-Fi list live in the flash FAT.
Unused pins. At boot every GPIO the firmware does not use is put in a safe state: input and output off and no pull resistor, held (the strapping pins 37 to 40 are not held), and the speaker amplifier’s enable (GPIO45) is driven low, so the amplifier stays off. The flash, USB, UART0 console and BOOT pins are never touched. This gives the same pin state at every boot. Its power saving is not measured.
The ESP-Mosaico is Espressif’s board. Its own documentation is at docs.espressif.com.